Pioneer AVH-1300NEX Installation Manual (2024)

AVH-2330NEX AVH-2300NEX AVH-1330NEX AVH-1300NEX

DVD RDS AV RECEIVER RÉCEPTEUR A/V RDS DVD RADIO AV RDS CON DVD

English Français Español

Installation Manual

Manuel d’installation

Manual de instalación

WARNIN G

CAUTION

Connection

WARNIN G

Ground wire

POWER AMP

Other devices (Another electronic device in the car)

Metal parts of car’s body

*1 Non supplied for this unit

ACC position

No ACC position

Precautions

Your new product and this manual

• Do not operate this product, any

applications, or the rear view camera option (if purchased) if doing so will divert your attention in any way from the safe operation of your vehicle. Always observe safe driving rules and follow all existing traffic regulations. If you experience difficulty in operating this product or reading the display, park your vehicle in a safe location and apply the parking brake before making the necessary adjustments.

• Do not install this product where it may

(i) obstruct the driver’s vision, (ii) impair the performance of any of the vehicle’s operating systems of safety features, including airbags, hazard lamp buttons, or (iii) impair the driver’s ability to safely operate the vehicle. In some cases, it may not be possible to install this product because of the vehicle type or the shape of the vehicle interior.

Important safeguards

Pioneer does not recommend that you install this product yourself. This product is designed for professional installation only. We recommend that only authorized Pioneer service personnel, who have special training and experience in mobile

2En

electronics, set up and install this product. NEVER SERVICE THIS PRODUCT YOURSELF. Installing or servicing this product and its connecting cables may expose you to the risk of electric shock or other hazards, and can cause damage to this product that is not covered by warranty.

Precautions before connecting the system

Do not take any steps to tamper with or disable the parking brake interlock system which is in place for your protection. Tampering with or disabling the parking brake interlock system could result in serious injury or death.

• Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wiring to remain exposed.

• Do not directly connect the yellow lead of

this product to the vehicle battery. If the lead is directly connected to the battery, engine vibration may eventually cause the insulation to fail at the point where the wire passes from the passenger compartment into the engine compartment. If the yellow lead’s insulation tears as a result of contact with metal parts, short- circuiting can occur, resulting in considerable danger.

• It is extremely dangerous to allow cables

to become wound around the steering column or shift lever. Be sure to install this product, its cables, and wiring away in such so that they will not obstruct or hinder driving.

• M ake sure that the cables and wires will

not inter fere with or become caught in any of the vehicle’s moving parts, especially the steering wheel, shift lever, parking brake, sliding seat tracks, doors, or any of the vehicle’s controls.

• Do not route wires where they will be

exposed to high temperatures. If the insulation heats up, wires may become damaged, resulting in a short circuit or malfunction and permanent damage to the product.

• Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resistor or filter, etc.) may fail to work properly.

• Never feed power to other electronic

products by cutting the insulation of the power supply lead of this product and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

Before installing this product

• Use this unit with a 12-volt battery and

negative grounding only. Failure to do so may result in a fire or malfunction.

• To avoid shorts in the electrical system,

be sure to disconnect the (–) battery cable before installation.

To prevent damage

• When speaker output is used by 4

channels , use speakers over 50 W (Maximum input power) and between 4 Ω to 8 Ω (impedance value). Do not use 1 Ω to 3 Ω speakers for this unit.

• When rear speaker output is used by 2 Ω

of subwoofer, use speakers over 70 W (Maximum input power).

*Please refer to connection for a connection method.

• The black cable is ground. When

installing this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the car’s body. The ground wire of the power amp and the one of this unit or any other device must be connected to the car separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire generation of smoke or malfunction.

• When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this product.

• This product cannot be installed in a

vehicle without ACC (accessory) position on the ignition switch.

• To avoid short-circuiting, cover the

disconnected lead with insulating tape. I t is especially important to insulate all

English

unused speaker leads, which if left

NOTE

uncovered may cause a short circuit.

• For connecting a power amp or other

devices to this product, refer to the manual for the product to be connected.

• The graphical symbol placed on

the product means direc t current.

Notice for the blue/ white lead

• When the ignition switch is turned on

(ACC ON), a control signal is output through the blue/white lead. Connect to an external power amp’s system remote control terminal, the auto-antenna relay control terminal, or the antenna booster power control terminal (max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even if the audio source is switched off.

This product

Microphone 3 m (9 ft. 10-1/8 in.) Wired remote input

Hard-wired remote cont rol adapter can be connected (sold separately).

Smartphone (Android™ device)

Connecting via the USB port

USB port USB cable 1.5 m (4 ft. 11 in.) USB - micro USB cable (Type USB A -

micro USB B) (supplied with CD-MU200 (sold separately))

4En

English

USB Type-C cable (Type USB A - USB C)

NOTE

WARNIN G

CAUTION

NOTES

NOTE

WARNIN G

(supplied with CD-CU50 (sold separately))

Smartphone

The length of Type USB A - micro USB B cable cannot exceed 2 m (6 ft. 6 in.) and Type USB A - USB C cannot exceed 4 m (13 ft. 1 in.) according to the USB cable standard. When using a cable other than the above conditions, the main unit function may not operate properly.

Camera

About rear view camera

When you use the rear view camera, the rear view image is automatically switched from the video by moving the shift lever to REVERSE (R). Camera View mode also allows you to check what is behind you while driving.

USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.

• The screen image may appear reversed.

• With the rear view camera you can keep

an eye on trailers, or back into a tight parking spot. Do not use for entertainment purposes.

• Object s in rear view may appear closer or

more distant than in reality.

• The image area of full-screen images

displayed while backing or checking the rear of the vehicle may differ slightly.

Rear view camera (ND-BC8) (sold

separately) To v ide o ou tpu t RCA cable (supplied with ND-BC8) This product Brown (R.C IN) Power supply Power cord Violet/white (REVERS E-GEAR SIGNAL

INPUT)

Refer to Power cord on page 3. Yel low (F. C IN )

(AVH-2330NEX/AVH-1330NEX) RCA cable (sold separately) View camera (sold separately)

• Connec t only the rear view camera to R.C IN. Do not connect any other equipment.

• Some appropriate settings are required

to use rear view came ras. For details, refer to the Operation Manual.

External video component and the display

Rear display with RCA input jacks To v ide o in put RCA cables (sold separately) This product Yel low (V IN) Yel low (V OUT) Red, white (R IN, L IN) AUX input Mini-jack AV cable (CD-RM10) (sold

separately) Yel low Red, white To Yellow To Red, white To v ide o ou tpu t

To a udi o ou tpu ts External video component (sold

separately)

The appropriate setting is required to use the external video component. For details, refer to the Operation Manual.

NEVER install the rear display in a location that enables the driver to watch the video s ource while driving.

This product’s rear video output is for connection of a display to enable passengers in the rear seats to watch the video source.

5En

CAUTION

Installation

Leave ample space

5 cm

sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.

Precautions before installation

Never install this product in places where, or in a manner that:

• Could injure the driver or passengers if

the vehicle stops suddenly.

• M ay interfere with the driver’s operation

of the vehicle, such as on the floor in front of the driver’s seat, or close to the steering wheel or shift lever.

• To ensure proper installation, be sure to

use the supplied parts in the manner specified. If any parts are not supplied with this product, use compatible parts in the manner specified after you have the part compatibility checked by your dealer. If parts other than supplied or compatible ones are used, they may damage internal parts of this product or they may work loose and the product may become detached.

• Do not install this product where it may

(i) obstruct the driver’s vision, (ii) impair the performance of any of the vehicle’s operating systems or safety features, including airbags, hazard lamp buttons or (iii) impair the driver’s ability to safely operate the vehicle.

• Never install this product in front of or

next to the place in the dashboard, door, or pillar from which one of your vehicle’s airbags would de ploy. Please refer to your vehicle’s owner’s manual for reference to the deployment area of the frontal airbags.

Before installing

• Consult with your nearest dealer if

installation requires drilling holes or other modification s of the vehicle.

• Before making a final installation of this

product, temporarily connect the wiring to confirm that the connections are correct and the system works properly.

Installation notes

• Do not install this product in places

subject to high temperatures or humidity, such as: – Places close to a heater, vent or air

conditioner.

– Places exposed to direct sunlight, such

as on top of the dashboard.

– Places that may be exposed to rain,

such as close to the door or on the vehicle’s floor.

• Install this product horizontally on a

surface within 0 to 30 degrees tolerance (within 5 degrees to the left or right). Improper installation of the unit with the surface tilted more than these tolerances increases the potential for errors in the vehicle’s location display, and might otherwise cause reduced display perfor mance.

• When installing, to ensure proper heat

dispersal when using this product, make

Installation using the screw holes on the side of this product

1 Fastening this product to the factory

radio-m ounting bracket.

Position this product so that its screw holes are aligned with the screw holes of the brack et, and tighten the sc rews at three locations on each side. Use either the truss head screws (5 mm × 8 mm) or flush surface screws (5 mm × 9 mm), depending on the shape of the bracket’s screw holes.

Fac tor y rad io- moun ting b rack et If the pawl interferes with

installation, you may bend it down

out of the way. Dashboard or console Truss head screw or flush surface

screw

Be sure to use the screws supplied

with this product.

Installing the microphone

• Install the microphone in a place where

its direction and distance from the driver make it easiest to pick up the driver’s voice.

• Be sure to turn off (ACC OFF) the product

before connecting the microphone.

• Depending on the vehicle model, the

microphone cable length may be too short when you mount the microphone on the sun visor. In such cases, install the microphone on the steering column.

Mounting on the sun visor

1 Fit the microphone lead into the

groove.

6En

English

Microphone lead

NOTE

Groove

2 Attach the microphone clip to the sun

visor.

Tab Microphone base

2 Mount the microphone on the

steering column.

Microphone clip Clamps

Use separately sold clamps to secure the lead where necessary inside the

vehicle . Install the microphone on the sun visor when it is in the up position. It cannot recognise the driver’s voice if the sun visor is in the down position.

Installation on the steering column

1 Detach the microphone base from the

microphone clip by sliding the microphone base while pressing the tab.

Double-sided tape Clamps

Use separately sold clamps to secure the lead where necessary inside the vehicle.

Keeping it away from the steering wheel.

Adjusting the microphone angle

7En

ATT ENTI ON

PRÉCAUTION

Connexion

ATT ENTI ON

Précautions

Votre nouveau produit et ce manuel

• N’utilisez pas ce produit, les applications

ou la caméra de recul en option (le cas échéant) si cela vous distrait de quelque façon affectant l’utilisation sécuritaire de votre véhicule. Respectez toujours les règles de conduite sécuritaire et toute la réglementation routière en vigueur. Si vous avez du mal à utiliser ce produit ou à voir l’affichage, stationnez votre véhicule dans un emplacement sûr et engagez le frein de stationnement avant d’effectuer les réglages nécessaires.

• N’installez pas ce produit là où il risque

(i) de gêner la vision du conducteur, (ii) d’affecter le fonctionnement de tout système ou de tout dispositif de sécurité du véhicule, y compris les coussins de sécurité gonflables ou les boutons de feux de détresse, ou (iii) d’affecter la capacité du conducteur à utiliser le véhicule de façon sécuritaire. Dans certains cas, il peut être impossible d’installer ce produit en raison du type de véhicule ou de la forme de l’intérieur du véhicule.

Importantes mesures de protection

Pioneer ne recommande pas d’installer ce produit soi-même. Ce produit est conçu pour être installé uniquement par des

professionnels. Il est recommandé de confier la configuration et l’installation de ce produit au personnel de service de Pioneer uniquement, qui a reçu une formation spéciale et a l’expérience des appareils électroniques mobiles. NE RÉPAREZ JAMAIS CE PRODUIT VOUS MÊME. En installant ou réparant vousmême ce produit et ses câbles de connexion, vous vous exposez à un risque de décharge électrique ou d’autres dangers et vous risquez de causer des dommages non couverts par la garantie à ce produit.

Précautions à prendre avant de connecter le système

Ne faites rien pour trafiquer ou désactiver le dispositif d’interverrouillage du frein de stationnement, mis en place pour assurer votre protection. Trafiquer ou désactiver le dispositif d’interverrouillage du frein de stationnement peut entraîner une blessure grave ou le décès.

• Fixez tous les câbles avec des serre-câbles

ou du ruban isolant. Ne laissez aucun fil nu exposé.

• Ne connectez pas le fil jaune de ce

produit directement à la batterie du véhicule. Si le fil est directement connecté à la batterie, les vibrations du moteur peuvent éventuellement endommager l’isolation au point où le fil passe de l’habitacle au compartiment moteur. Si l’isolation du fil jaune s’use au

contact des pièces métalliques, cela peut causer un court-circuit très dang ereux.

• Il est extrêmement dangereux de laisser

les câbles s’enrouler autour de la colonne de direction ou du levier de vitesse. Assurez-vous d’installer ce produit, ses câbles et ses fils à l’écart, de sorte qu’ils ne gênent pas la conduite.

• Assurez-vous que les câbles et fils ne

gêneront pas ou ne seront pas coincés par les pièces mobiles du véhicule, et tout particulièrement le volant de direction, le levier de vitesse, le frein de stationnement, les rails de siège coulissant, les portières ou toute commande du véhicule.

• Ne posez pas les fils à des emplacements

exposés à des températures élevées. La surchauffe de l’isolation peut endommager les fils, entraînant un courtcircuit ou un problème de fonctionnement et des dommages permanents au produit.

• Ne raccourcissez aucun fil. Autrement, le

circuit de protection (porte-fusible, résistance de protection ou filtre, etc.) risque de ne pas bien fonctionner.

• N’alimentez jamais d’autres produits

électroniques en coupant l’isolation du fil d’alimentation de ce produit pour y connecter un autre fil. La capacité du fil serait dépassée, entraînant une surchauffe.

Avant d’installer ce produit

• N’utilisez cet appareil qu’avec une

batterie 12 volts avec masse négative. Autrement, il y a risque d’incendie ou de problème de foncti onnement.

• Pour éviter de court-circuiter le système

électrique, pensez à déconnecter le câble de batterie (–) avant l’installation.

Pour éviter les dommages

• Lorsque la sortie de haut-parleur est

utilisée par 4 canaux, utilisez des hautparleurs de plus de 50 W (Puissance d’entrée maximale) et de 4 Ω à 8 Ω (valeur d’impédance). N’utilisez pas de hautparleurs de 1 Ω à 3 Ω avec cet appareil.

• Lorsque la sortie de haut-parleur arrière

est utilisée par un caiss on d’ex trêmes graves de 2 Ω, utilisez des haut-parleurs de plus de 70 W (Puissance d’entrée maximale ). *Veuillez vous reporter aux connexions pour connaître la méthode de connexion.

• Le câble noir est le câble de masse. Lors

de l’installation de cet appareil ou d’un amplificateur de puissance (vendu séparément), pensez à connecter d’abord le fil de masse. Assurez-vous que le fil de masse est bien connecté à une partie métallique de la carrosserie du véhicule. Le fil de masse de l’amplificateur de puissance et celui de cet appareil ou de tout autre dispositif doivent être connectés au véhicule séparément, avec des vis différentes. Si la vis d u fil de masse se desserre ou tombe, il y a risque d’incendie et de génération de fumée ou de problème de fonctionnement.

2Fr